Victron Complete Charger (20A)


Victron Complete Charger (20A)

from 690.00

Communicates battery voltage and solar charge rate to a smart phone or tablet via Bluetooth, Expandable up to 300W, Advanced MPPT charge controller delivers approximately 20% more energy than PWM, Combiner box covers roof penetration and allows for easy upgrades, Panel(s) can be tilted

Array Configuration:
Add To Cart

This kit that offers everything needed to put solar power onto an existing battery bank.  With the advanced MPPT charge controller and Bluetooth communication, this kit forms the ideal foundation for a small power system mounted to a metal roof.  Adding panels, a lithium battery bank and an inverter system will make it possible to run larger loads like a refrigerator, microwave, coffee maker, TV, etc.  No matter how much solar you have, running a heater or air conditioner is not likely feasible.

Wiring Diagram

What You Get:

0-3x SOLAR-ZS90S Solar Panel Z90 Short
0-3x SOLAR-ZS90L Solar Panel Z90 Long
0-1x SOLAR-ZS170 Solar Panel Z170

1-3x 91M-35MZ Mount Set - 35mm Zamp
1x CCTLR-VT-VT-MPPS-020A SunRunner Victron MPPT 20A
30'    CABLE-8GA-2-GRY        Duplex-8/2
1x    92C-INTR        Interior Wire Harness Acc. Kit
1x    93F-ATC-020A        20A ATC Fuse Kit
1x    93T-NEG-8GA        8ga Negative Terminal Kit
1x    93S-MINI        Switch-Mini On/Off w/Screws
2x    LUG-8GA-RING-3/8        8 ga. Lug-3/8" Ring
2"    HS-RED-HD-1/2        Heat Shrink 1/2" Red
1-3x 93C-ZCBNR Zamp Plug & Strain relief for C-Box
1x 20-ROOF Roof Combiner Box
1x SEAL-SKF Sikaflex 221
1x SEAL-SLVL Dicor Self Leveling Sealant (for the combiner box)

You may also be interested in:

Victron BMV-712 Battery Monitor Kit

Battery monitor kit with programmable relay.  Measures voltage, current, capacity, and temperature.  Can work with any battery type.  Built-in Bluetooth.  Compatible with the Color Control Monitor.

Monitor Dimensions:  H 1.3" x W 2.4" x D 2.4"
Shunt Dimensions:  H 1.4" x W 4.8" x D 1.6"
Cable Length: 10m

Add To Cart
Victron MPPT Control Kit

This kit provides a remote monitor with programming capability for Victron MPPT charge controllers.

Add To Cart
Tilt Bar Set - 15.5" / 45°

For tilting the SF100 and SP100 solar panels at a 45 degree angle for increased output in the winter months.  Made from corrosion resistant stainless steel.

Add To Cart
Dicor Sealant

Dicor protects the VHB tape from the elements.  Use it to seal around mount feet, cable management hardware and combiner boxes attached to roofs.

Add To Cart
Tilt Bar Set - 19.5" / 45°

For tilting the ZS170 solar panel at a 45 degree angle for increased output in the winter months.  Made from corrosion resistant stainless steel.

Add To Cart

AM Solar Part Number:  99-VT0201x90S, 99-VT0201x90L, 99-VT0201x170, 99-VT0202x90S, 99-VT0202x90L, 99-VT0201x90S1x90L, 99-VT0203x90S, 99-VT0203x90L,